Can an older lower-clearance warehouse accommodate both faces?

Possibly. The assessment must include the height difference across the lane, loaded pallet dimensions and forklift placement clearance. A lower level count or shorter channel may be appropriate; floor area alone cannot establish feasibility.

Will rollers manage wine shipment lot numbers?

No. They present pallets in loading sequence, but staff and inventory procedures must maintain lot assignments. Separate lanes may be needed where different lots must remain independently accessible for release or dispatch.

What if healthcare suppliers change their pallet bases?

The new base must be checked against the specified roller contact and support requirements before loading. Similar dimensions do not establish equivalent travel, particularly when board direction, stiffness or runner arrangement changes.

Should varied contractor supply items occupy deep channels?

No. Repeated quantities make better candidates than products requiring frequent individual selection. A combined layout can reserve flow channels for steady movers while keeping varied or low-volume inventory in another storage format.

Pallet Flow Rack system inside a New Mexico warehouse

Santa Fe, New Mexico

Pallet Flow Rack in Santa Fe, NM

Pallet flow rack in Santa Fe can concentrate repeated inventory into gravity-fed lanes while preserving a defined replenishment side and retrieval side. In a limited industrial footprint, that is worth evaluating carefully: deeper storage only helps when pallet quantities, building clearance and access routes support the proposed arrangement.

Siler Road industrial properties and the Airport Road corridor offer relevant settings for reviewing available space rather than assuming a large distribution building. Wine and spirits distribution can require deliberate date or lot sequencing, while healthcare logistics may combine repeat supplies with many smaller inventory lines requiring separate selection.

(505) 436-7469

A Building-First Installation Process

Read the building envelope

Review clear height, obstructions and the routes between receiving and dispatch. Account for the raised loading end and the lift needed to place pallets, rather than checking only the height of the retrieval face.

Match lanes to stock groups

Separate repeat pallet quantities from mixed, slower inventory. Review lot control, dated stock and replenishment quantities to choose channel depths that the operation can actually fill without creating inaccessible pockets of unused capacity.

Set the handling specification

Record pallet dimensions, board patterns and minimum and maximum loads. Use those inputs to select roller support and movement control, then define which pallet conditions operators must reject before loading a channel.

Confirm installed behavior

Coordinate crew access and material placement with site staff. Check representative pallets through entry, gravity travel and discharge, then explain lane assignments, loading direction and the agreed response to abnormal movement before routine operation.

Pallet Flow Rack Planning Within Building Limits

Our pallet flow racking recommendations start with the constraints of the room. Older, lower-clearance buildings require particular attention to the elevated loading end, loaded pallet height and forklift approach. We compare storage depth with working access before proposing additional levels or assigning every product a flow lane.

You work with a division of Warehouse Equipment & Supplies Co., supplying and installing since 1997. The equipment scope uses new material only, installed through managed crews. We connect the proposed arrangement to written pallet requirements and operating boundaries rather than relying on a drawing alone.

Planning also considers how the warehouse functions around the work area. For sites near Rufina Street or Pacheco Park, the discussion centers on actual delivery access and internal circulation. We establish installation boundaries and material staging arrangements without assuming the entire building can be cleared.

Read the building envelope

Match lanes to stock groups

Set the handling specification

Pallet flow rack lanes with gravity rollers installed

Flow racking system loaded with pallets at the pick face

Managing Lots at Each Face

Santa Fe service area

Government and contractor supply

Specialty manufacturing

Wine and spirits distribution

Healthcare logistics

Pallet Flow Racking for Controlled Rotation

A gravity flow rack system moves loads on rollers down a selected slope. Depth determines how many pallets travel through a channel and how much inventory is committed to one assignment. We relate those choices to batch sizes and shipment frequency, especially where available floor area is constrained.

Pallet boards are a design input, not a minor purchasing detail. Their orientation, spacing and condition determine contact with the roller tracks. The assessment includes loaded deflection and overhang so the base remains supported and the product does not interfere with neighboring lanes during travel.

Speed controllers or brakes govern movement within the specified load range. Light loads must overcome rolling resistance without manual assistance inside a channel; heavy loads need controlled descent and suitable discharge behavior. Where appropriate, a separator isolates the front pallet from following pallet pressure during picking.

Opposite load and pick faces support FIFO when dated or high-volume SKUs are replenished in the correct sequence. Pushback instead receives and retrieves pallets at one face, normally giving last-in, first-out access within a lane. The comparison turns on rotation needs and aisle availability, not density alone.

Read the building envelope

Match lanes to stock groups

Set the handling specification

Confirm installed behavior

Call (505) 436-7469